eMaxMobileApp 1.73
Paid Version
Publisher Description
All Bluetooth capable displays SC-EM800, SC-E8000, SC-E7000, SC-E6100, SW-EN600-L switch and EW-EN100 cockpit are supported!
Additionally to DU-E80X0 motors, now DU-EP801, DU-EP800, DU-EP600, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
Partially compatible also with the latest Shimano motor firmware versions!
See www.eMax-Tuning.com or get detailed & personal information via eMail from info@eMax-Tuning.com
Apr 15, 2024
Version 1.73
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.73 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
About eMaxMobileApp
eMaxMobileApp is a paid app for iOS published in the Health & Nutrition list of apps, part of Home & Hobby.
The company that develops eMaxMobileApp is Markus Schlegel. The latest version released by its developer is 1.73.
To install eMaxMobileApp on your iOS device, just click the green Continue To App button above to start the installation process. The app is listed on our website since 2024-04-15 and was downloaded 22 times. We have already checked if the download link is safe, however for your own protection we recommend that you scan the downloaded app with your antivirus. Your antivirus may detect the eMaxMobileApp as malware if the download link is broken.
How to install eMaxMobileApp on your iOS device:
- Click on the Continue To App button on our website. This will redirect you to the App Store.
- Once the eMaxMobileApp is shown in the iTunes listing of your iOS device, you can start its download and installation. Tap on the GET button to the right of the app to start downloading it.
- If you are not logged-in the iOS appstore app, you'll be prompted for your your Apple ID and/or password.
- After eMaxMobileApp is downloaded, you'll see an INSTALL button to the right. Tap on it to start the actual installation of the iOS app.
- Once installation is finished you can tap on the OPEN button to start it. Its icon will also be added to your device home screen.
Program Details
General |
|
---|---|
Publisher | Markus Schlegel |
Released Date | 2024-04-15 |
Languages | English |
Category |
|
---|---|
Category | Home & Hobby |
Subcategory | Health & Nutrition |
System requirements |
|
---|---|
Operating systems | ios |
Download information |
|
---|---|
File size | 12.58 MB |
Total downloads | 22 |
Pricing |
|
---|---|
License model | Paid |
Price | $0.99 |
Version History
version 1.73
posted on 2024-04-15
Apr 15, 2024
Version 1.73
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.73 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
version 1.72
posted on 2024-03-27
Mar 27, 2024
Version 1.72
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.72 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
version 1.71
posted on 2024-02-09
Feb 9, 2024
Version 1.71
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.71 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.20
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
version 1.70
posted on 2023-10-23
Oct 23, 2023
Version 1.70
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.70 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
version 1.69
posted on 2023-10-09
Oct 9, 2023
Version 1.69
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.69 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
version 1.68
posted on 2023-09-29
Sep 29, 2023
Version 1.68
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.68 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
version 1.67
posted on 2023-09-11
Sep 11, 2023
Version 1.67
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.67 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
version 1.66
posted on 2023-09-07
Sep 7, 2023
Version 1.66
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.66 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
version 1.63
posted on 2023-04-01
Apr 1, 2023
Version 1.63
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.63 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
version 1.62
posted on 2023-03-21
Mar 21, 2023
Version 1.62
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.62 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
version 1.54
posted on 2022-07-10
Jul 10, 2022 Version 1.54
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.54 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
version 1.51
posted on 2022-03-30
Mar 30, 2022 Version 1.51
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.51 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.
new in version 1.51 (29.03.22):
-update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
-update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
-update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
-new battery type BT-E8016 added
ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved
version 1.47
posted on 2021-11-25
Nov 25, 2021 Version 1.47
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.47 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.
new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
-new battery type BT-E8016 added
ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved
version 1.46
posted on 2021-11-19
Nov 19, 2021 Version 1.46
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.46 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.
new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
-new battery type BT-E8016 added
ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved
version 1.45
posted on 2021-09-08
Sep 8, 2021 Version 1.45
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.45 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.
new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
-new battery type BT-E8016 added
ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved
ver. 1.39 (31.01.21):
-integration of new motor firmware version 4.1.2 for EP8
-extended light indication for EP8 (off/manual/on & max. power)
-chainring - size and sprocket size with all possible correct values now for EP8
-correction of indication of motor firmware version
-correction of minor text errors
ver. 1.38 (26.11.20):
-new battery type BT-E8036 added
-special settings (derailleur type, etc.) added for DUEP800
ver. 1.36 (08.11.20):
-partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-licence placeholdertext in darkmode improved (grey)
-new battery types added
-correction of AS - settings
-optimized "dark mode" handling for licence key entry boxes
-light activating functionality added
-motor mounting angle added
-optimized country specific decimal characters for total distance (odd)
ver. 1.35 (31.08.20):
-integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-minor bug fixing and optimizations
ver. 1.34 (13.07.20):
-DUE80X0: compatibility with newest motor firmware 4.8.0
ver. 1.33 (18.05.20):
-6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted